Interlaboratory comparisons and improvements of methods for acid number determination in used motor oils

The results of two interlaboratory comparisons of acid number determinations in used motor oils are discussed. It is shown that the comparability of the measurement results is not as good as that required by known standards for petroleum products. The problem is motor oil contaminants which accumulated during use, and which are the source of a matrix effect in the acid number determination. The standard methods’ drawbacks are analyzed and some improvements are proposed. Repeatability and accuracy of the improved methods are evaluated. Received: 11 December 2001 Accepted: 15 February 2002     

Refractive index of standard oils as a function of wavelength and temperature

The refractive indices (n) of eight standard oils from Physikalisch Technische Bundesanstalt, Germany were determined with an accuracy of ±1×10⁻⁴ by using Abbe Refractometer. The measurements were performed at temperature 20°C in the spectral range 0.4–0.7 μm. The experimental data were fitted to the simple Cauchy dispersion formula and the results were found to be consistent within the limits of experimental error. In all cases, the refractive index decreased monotonically with increasing wavelength. The refractive indices (n) of these oils have been measured as a function of the temperature t (20°C up to 50°C) at λ=0.589 μm and were found to have linear temperature dependencies. The refractive indices of the studied oils and the uncertainty in their values are calculated at λ=0.589. The Lorentz–Lorenz (L–L) formula has been tested and it was found to be valid with a maximum deviation of 0.4% and was used to calculate the molecular polarizability θ.     

塞曼石墨炉原子吸收光谱法直接测定垃圾焚烧废气中锡

采用钯加抗坏血酸溶液作为基体改进荆，用塞曼效应扣除背景，对消化后的垃圾焚烧废气滤筒直接进行测定。方法的检出限为100pg，线性范围为0．2～4ng，回收率为96．8％～102．0％。     

Polygermoxanes suitable for biochemical purposes. Part I. Digermoxanes (low-viscosity oils)

In order to replace silicones in some of their biomedical applications, e.g. syringe lubrication, implants ets., a series of digermoxanes (R¹R²R³Ge)₂O (R = n–alkyl, aryl) were synthesized. These compounds are thermally stable oils; their viscosities, depending on the nature of substituents, lie in the range 1–72 cPo (mPa s) at 20°C.     

超声波在废橡胶再生中应用的最新进展

全世界每年产生大量废旧橡胶，它们需要很长时间才能降解，这既污染环境，又浪费资源，解决此问题的唯一方法是再生利用。在众多再生方法中，新近出现的超声波脱硫再生法，被认为是最有希望的方法，本文详细地介绍了这方面的最新进展情况。     

Determination of the boiling point distribution of sulfur compounds in light cycle oil using GC with a flame photometric detector and pyrolyzer

A method has been developed to determine the boiling point distribution of sulfur compounds in light cycle oils (LCO'S). The method chosen for this analysis was GC with a flame photometric detector (FPD) and pyrolyzer. Tests were carried out to evaluate the recovery efficiency, repeatability, and accuracy of the method. Repeatabilities within 2% were obtained. The recovery of benzothiophenes and dibenzothiophenes was close to 100%; this was important because these are the major sulfur components in LCO's. No hydrocarbon or solvent interferences were observed with the use of the pyrolyzer, even for a 95% solvent level. Comparison with results from other techniques showed that the method accurately determined the levels of sulfur compounds in the LCO boiling point range.     

Ultrasonic analysis of edible fats and oils

Low intensity ultrasound is a powerful analytical technique for investigating the physico-chemical properties of many biological and non-biological materials. In this article its application for the characterization of edible fats and oils is assessed. Ultrasound can be used to determine the dynamic rheology and composition of oils, the oil content and droplet size of emulsions and the solid fat content of partially crystalline emulsions. It is capable of rapid and precise measurements, is non-destructive and non-invasive, can be used on-line or off-line and is relatively inexpensive. Ultrasonic techniques will therefore prove a useful addition to the existing analytical techniques used to characterize fats and oils.     

Development and critical comparison of greener flow procedures for nitrite determination in natural waters

Two greener procedures for flow-injection spectrophotometric determination of nitrite in natural waters were developed and critically compared. Replacement of toxic reagents, waste minimization and treatment were exploited to attend the standards of clean chemistry. The flow system was designed with solenoid micro-pumps in order to minimize reagent consumption and waste generation. The first procedure is based on the Griess diazo-coupling reaction with sulfanilamide and N-(1-naphthyl)ethylenediamine (NED) yielding an azo dye, followed by photodegradation of the low amount of waste generated based on the photo-Fenton reaction. The second procedure is based on the formation of iodine from nitrite and iodide in acid medium in order to avoid the use of toxic reagents. For Griess method, linear response was achieved up to 1.0 mg L^− 1, described by the equation A = − 0.007 + 0.460C (mg L^− 1), r = 0.999. The detection limit was estimated as 8 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.8% (n = 20). The sampling rate was estimated as 108 determinations per hour. The consumption of the most toxic reagent (NED) is reduced 55-fold and 20-fold in comparison to batch method and flow injection with continuous reagent addition, respectively. A colorless residue was obtained by in-line photodegradation with reduction of 87% of the total organic carbon content. The results obtained for natural water samples were in agreement with those achieved by the reference method at the 95% confidence level. For the nitrite–iodide method, linear response was observed up to 2.0 mg L^− 1, described by the equation A = − 0.024 + 0.148C (mg L^− 1), r = 0.999. The detection limit was estimated as 25 μg L^− 1 at the 99.7% confidence level and the coefficient of variation was 0.6% (n = 20). The sampling rate was estimated as 44 determinations per hour. Despite avoiding the use of toxic reagents, the nitrite–iodide method presented worst performance in terms of selectivity and sensitivity.     

Evaluation of gas chromatography-tandem quadrupole mass spectrometry for the determination of organochlorine pesticides in fats and oils

A gas chromatography-tandem quadrupole mass spectrometry multi-residue method for the analysis of 19 organochlorine pesticides in fats and oils has been developed. Gel permeation chromatography was employed to remove lipid material prior to GC-MS/MS analysis. Average recoveries of the pesticides spiked at 10 and 50 microg kg(-1) into fish oil, pork fat, olive oil and hydrogenated vegetable oil were typically in the range 70-110% with relative standard deviations generally less than 10%. Calculated limits of detection are between 0.1 and 2.0 microg kg(-1) and results obtained for the analysis of proficiency test materials are in good agreement with assigned values. The higher selectivity of the GC-MS/MS compared to electron capture detection and GC-MS in selective ion monitoring mode allowed unambiguous identification and confirmation of all the target pesticides at low microg kg(-1) levels in fats and oils in a single analysis.     

Characterization of some essential oils and their key components: Thermoanalytical techniques

The present study was aimed at determining the kinetics of evaporation and establishing vapor pressure curves for both single and multi-component systems by thermogravimetry (TG) and differential scanning calorimetry (DSC). Essential oils (e.g. lavender oil, orange oil, clove oil and eucalyptus oil, etc.) are typically multi-component systems consisting of various volatile pure components (e.g. linalyl acetate, limonene, cinnamaldehyde, etc.) which resemble single component systems. In this study linalyl acetate was taken as the calibration compound for TG. The vapor pressure curves for the pure substances were plotted using TG and vapor pressure plots for clove oil and eucalyptus oil were constructed using DSC. The thermodynamic and kinetic parameters of the pure compounds were compared to that of the multi-component systems to quantitatively and qualitatively measure the influence of different compounds on each other. The k-value from the vapor pressure data for linalyl acetate was calculated as 112006 Pa kg^0.5mol^0.5s^-1 m^-2 K^-0.5. The vapor pressure values were used to determine the Antoine constants using the SPSS 10.0 software.This revised version was published online in November 2005 with corrections to the Cover Date.